Download over 500 Boat PlansDownload Now

Load Distribution Calculator

Analyze weight placement and center of gravity for your boat.

Quick Samples
Try these common configurations to get started

30ft Cruiser

25ft Sailboat

18ft Runabout

Hull Dimensions
Enter your boat's principal dimensions
Boat Dimensions
Load Items
Download 500+ Boat Plans
About This Tool
This Load Distribution Calculator is a critical tool for boat designers and builders. It helps determine the vessel's center of gravity (CG) based on the weight and location of all items on board. Proper weight distribution is fundamental to a boat's stability, safety, handling, and performance.

Key Concepts:

Center of Gravity (CG): The single point where the boat's total weight is concentrated.
Longitudinal Balance: Fore-and-aft balance, affecting the boat's trim.
Lateral Balance: Port-and-starboard balance, affecting the boat's heel or list.
Stability: The boat's ability to resist tipping and return upright.
Download 500+ Boat Plans
Get access to a comprehensive library of boat plans and tutorials.

"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.

Download Now
Load Distribution Calculator: What It Does and Why It Matters

Load distribution is the practical cousin of centre of gravity: instead of a single number it shows you how the weight you actually carry sits along, across and up the boat, and whether that spread leaves the vessel balanced or listing toward one trouble spot.

A hull can hold all the right components and still sail badly if they are clustered aft, heaped to one side or stacked high. By placing each item in the boat's own coordinate frame the tool exposes the resulting moments and balance so you can rearrange before you glass anything down.

Enter the boat length and beam, then add each load with its weight and its three positions, and the calculator returns the combined centre of gravity, the longitudinal and lateral balance and a stability rating for the arrangement you have proposed.

The Load Distribution Formula
CG = Σ(weight × position) ÷ Σweight; Longitudinal balance = |CGx − L/2| ÷ (L/2)
  • Σweight — Total of all load items
  • CGx, CGy, CGz — Centre-of-gravity coordinates along, across and up
  • L — Boat length used for the reference axis
  • Longitudinal balance — How far the CG sits from amidships, as a fraction
  • Lateral balance — How far the CG sits off the centreline
Worked Example: Load Distribution Step by Step
  1. 1On a 30 ft hull you place 500 lb of engine at the 24 ft mark and 300 lb of tankage at the 12 ft mark.
  2. 2Total weight: 500 + 300 = 800 lb.
  3. 3Longitudinal moment: 500 × 24 + 300 × 12 = 12,000 + 3,600 = 15,600.
  4. 4CG along the length: 15,600 ÷ 800 = 19.5 ft, well aft of the 15 ft amidships point.
  5. 5The balance figure then flags that rearward bias, telling you to shift tankage aft, move gear forward, or expect a squatting, heavy-steering boat.
How to Use This Calculator
  1. Enter overall length and beam as your frame.
  2. Add each load with weight and x, y, z position.
  3. Keep positions consistent from a chosen reference.
  4. Press Calculate to read the CG and balance scores.
  5. Re-arrange weights and watch the rating improve.
Load Distribution Reference Table
ArrangementLongitudinalLateralResult
Evenly spreadNear 0Near 0Balanced, neutral helm
Weight aftAft-biasedLowSquat, heavy steering
Weight forwardFwd-biasedLowDiving, plugs in chop
One-sidedLowHighPermanent list, weather helm

How clustered weight shows up in the balance scores.

What This Means in a Real Build
  • Symmetry first. Even a modest one-sided weight gives a list you can never fully trim out under way, so mirror tankage, batteries and lockers across the centreline.
  • Fighting the aft cluster is the most common DIY fix. Outboards, live wells and heavy gear love to gather at the transom; move what you can forward before you accept the trim.
  • Treat movable load as part of the plan. Crew, coolers and fuel that shift around change the picture constantly, so design for the worst realistic arrangement, not the showroom-empty one.
  • Low beats light once, but low and centred beats both. When you must carry weight, choose a position that serves both vertical and lateral balance at the same time.
  • Recompute after every late change. Adding a windlass or a bigger tank late in the build quietly repartitions the whole boat, and it is cheap to check on paper than to correct in glass.

Formula verified against standard naval-architecture references · Updated October 2026

Load Distribution Calculator: Frequently Asked Questions

What is load distribution and why care?

Load distribution is how a boat's weight is spread fore-to-aft, side-to-side and top-to-bottom, rather than lumped at one point. Two boats can weigh the same yet behave completely differently depending on where that weight sits. Poor distribution causes list, bad trim, heavy steering, a tender or cranky motion and wasted performance, so planning where each load lives is as important as how heavy it is.

How do I find the centre of gravity from my loads?

Multiply each item's weight by its distance from a chosen reference in each direction to get its moment, add all the moments, and divide by the total weight. The result is the weighted-average position, or centre of gravity, in that axis. Doing it for length, offset and height gives the full three-dimensional CG, which this calculator assembles from your list of loads.

What is a good longitudinal balance?

You generally want the combined CG close to the point where the hull planes or sails in equilibrium, which for a displacement hull sits near amidships and for a planing hull a little aft of it. A large fore or aft offset shows up as squatting, bow-down plugging or an unbalanced helm, so aim to keep the CG within a few percent of the target and tune with tankage and gear placement.

Does lateral balance matter on a sailboat?

Very much. A CG off the centreline makes the boat heel under sail even in light air, raises weather helm and costs windward performance, and it is nearly impossible to correct once the hull is built. Sailboats rely on ballast centred on the keel, so keep engines, tanks and gear symmetrically placed and reserve deliberate offset only for rare, calculated reasons.

How is this different from the centre-of-gravity calculator?

Both compute the same weighted-average CG; the difference is emphasis. The centre-of-gravity tool frames it as a stability input across load cases, while this one stresses the balance scores and the visual spread of clustered weight along and across the boat, encouraging you to rearrange items. Use whichever suits the question, the underlying arithmetic is identical.

Can I fix a bad load plan after building?

Sometimes, by relocating movable and removable weight. Sliding batteries, adding water or lead ballast low and centred, and moving tankage can correct modest imbalances. Structural weight fixed high or far aft is hard to undo, which is exactly why working the distribution on paper before glassing is far cheaper than repairing it at the dock.

How do I keep the load path continuous?

Every point where a rigging load enters the boat needs an unbroken route down to structure that can carry it, and the failure mode builders miss is the gap between fitting and frame. A chainplate bolted to a deck that ends at a thin bulkhead, or an engine bed resting on panels that do not meet the frames, concentrates force where nothing was designed to take it. Trace each load from masthead or through-hull to the keel or spring line and make sure fasteners, backing plates and the members behind them share the same line of pull. When a member must change direction, overlap and glass or bolt the joint generously, because load paths fail at their weakest discontinuity, not their average.

Sources & Further Reading
  • The Backyard Boatbuilder — Daniel St. John Green
  • Principles of Yacht Design — Larsson, Eliasson & Ranslet
  • Elements of Yacht Design — Francis Hervey Skene