Download over 500 Boat PlansDownload Now

Epoxy Resin Calculator

Calculate precise epoxy resin and hardener quantities for boat building applications

Quick Samples
Try these common configurations to get started

Hull Coating - 30ft Sailboat

Standard hull coating

Deck Laminating - 25ft Powerboat

Deck laminating

Fairing Compound - Hull Repairs

Hull fairing

Hull Dimensions
Enter your boat's principal dimensions
Download 500+ Boat Plans
About This Tool
The Epoxy Resin Calculator helps you determine the precise amount of resin and hardener needed for your boat building project. It takes into account the application type, epoxy system, surface area, thickness, and environmental conditions to provide an accurate estimate of your material requirements.

Key Concepts:

Mix Ratio: The specific ratio of resin to hardener required for a proper cure. This varies by epoxy system.
Pot Life: The amount of time you have to work with a mixed batch of epoxy before it begins to gel.
Working Time: The time you have to apply and tool the epoxy before it becomes unworkable.
Waste Factor: An extra amount of epoxy to account for material left in mixing cups, on rollers, and other waste.
Download 500+ Boat Plans
Get access to a comprehensive library of boat plans and tutorials.

"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.

Download Now
Epoxy Resin Calculator: What It Does and Why It Matters

Epoxy is the glue, the coating and the matrix that holds a modern DIY hull together, and running short mid-project is one of the most frustrating ways to lose a day. Ordering enough, and mixing it in the right ratio, keeps your layups wet-out and your fillets continuous.

The amount you need depends on the area, the number of coats, the target thickness and, crucially, the resin-to-fabric or resin-to-hardener ratio of the system you choose. A coating spread differs from a saturation soak, so the same square footage can drink very different volumes.

Enter your surface area, coat count, thickness and product system, set a waste allowance, and the calculator returns the resin, hardener and total mixed volume, plus a cost estimate so you buy once and buy enough.

The Epoxy Resin Formula
Resin (gal) = (Area × Coats) ÷ Spread-rate; Hardener = Resin ÷ Mix-ratio; Total = (Resin + Hardener) × (1 + Waste)
  • Area — Surface to be coated or laminated in square feet
  • Coats — Number of passes applied
  • Spread-rate — Square feet per gallon the system covers per coat
  • Mix-ratio — Resin-to-hardener ratio, for example 5:1 by volume
  • Waste — Allowance for spillage, thickening and substrate soak-up
Worked Example: Epoxy Resin Step by Step
  1. 1You plan to coat 100 square feet of hull in two coats with a 5:1 system covering about 50 ft² per gallon.
  2. 2Resin for the coats: 100 × 2 ÷ 50 = 4 gallons.
  3. 3Hardener at 5:1: 4 ÷ 5 = 0.8 gallon.
  4. 4Add a 10 percent waste allowance: 4.8 gallons of resin and 0.88 of hardener.
  5. 5So budget roughly 4.8 gal of resin and 0.9 gal of hardener, ordering a matched kit that covers that mixed volume rather than guessing by eye at the mixing cup.
How to Use This Calculator
  1. Measure the total surface area to be wetted.
  2. Choose your epoxy system so the ratio and spread rate match.
  3. Set coats and any target film thickness.
  4. Add a realistic waste percentage for the substrate.
  5. Press Calculate to read resin, hardener and cost.
Epoxy Resin Reference Table
TaskTypical Spread (ft²/gal/coat)Note
Seal coat60 - 80Thin, thirsty first pass
Finish coating45 - 55Smooth, closed surface
Plain laminate 6 oz35 - 45Fabric soaks more
Biax / heavy cloth25 - 35Thicker cloth, more resin

Approximate spread and ratio for common epoxy tasks.

What This Means in a Real Build
  • Porous or rough substrates demand the 15 to 25 percent waste end of the range; a smooth cured surface lets you drop toward 10 percent.
  • Heavier cloth soaks far more resin than a light seal coat, so never size a laminating job by the numbers for coating a fair surface.
  • Mix strictly to the stated ratio. Too little hardener leaves a tacky cure; too much makes it brittle and can cause exotherm in a thick mass.
  • Hot shops cut pot life sharply. Mix smaller batches in summer and plan your layup sequence before you combine the two parts.
  • Order matched kits rather than separate drums; it keeps the ratio honest and the stock dated, and old resin that has thickened or crystallised is a false economy.

Formula verified against standard naval-architecture references · Updated October 2026

Epoxy Resin Calculator: Frequently Asked Questions

How much epoxy do I need per square foot?

It depends entirely on the task. A thin seal or finish coat covers roughly 45 to 80 square feet per gallon per coat, while saturating woven fabric soaks much more, sometimes only 25 to 45 square feet per gallon depending on cloth weight. A good rule is to measure area, decide coats and cloth, then let the spread rate drive the volume rather than judging by the eyeball, because under-ordering mid-layup is the classic disaster.

What is the resin-to-hardener ratio?

Marine epoxies come at set ratios by volume or weight, commonly anywhere from 1:1 to 5:1, and the correct one is printed on the kit. Do not treat ratios as interchangeable between brands or even between slow and fast hardeners from the same maker. Using the wrong proportion prevents a proper cure, so always confirm the specific system's ratio before mixing, and measure it accurately.

Should I add a waste allowance?

Yes, every time. Some fraction of every batch is left in the cup, thickened for fillets, soaked into a thirsty surface, or lost to a rushed edge. Ten percent suits a smooth, well-controlled job; fifteen to twenty-five percent is prudent for rough or porous substrates, awkward overhead work, or when you are learning. The small over-order is cheap against running dry on a half-wet lap.

Why does heavy cloth need more resin?

Fibreglass fabric displaces and absorbs resin in proportion to its weight and weave. A light seal coat lays down a thin film, but saturating a heavy biaxial cloth means filling the space between and within the fibres, which can more than double the resin per square foot. That is why laminating spread rates are far lower than coating rates, and why sizing a laminate from coating numbers under-orders.

Can I change the ratio to make epoxy cure faster?

Not safely. The ratio is a chemical stoichiometry, not a dial, and over-hardening does not reliably speed the cure; it leaves an uncured or brittle film and can drive dangerous exotherm in bulk. If you need faster work in cold conditions, warm the shop and the materials, or use the manufacturer's fast hardener, rather than doctoring the mix.

How do I stop epoxy overheating in the bucket?

Exotherm is a mass effect: a large, still volume of mixed epoxy traps its own heat and can smoke, boil or scorch. Mix and work in small batches, decant into shallow containers, keep the shop cool and follow the recommended pot life. On hot days, laminating large areas, split the job across several modest batches instead of one big pour.

What happens if I get the mix ratio wrong?

Epoxy cures by a chemical reaction between resin and hardener in a fixed proportion, so drifting from that ratio leaves the network incomplete no matter how long you wait. Too little hardener gives a soft, tacky film that never reaches full strength and stays vulnerable to water; too much can leave a brittle, blush-prone cure and, in a thick mix, drive a fast exotherm that overheats and weakens the bond. Small deviations of a few percent by volume are usually tolerated by modern slow hardeners, but weigh on a scale when you can, mix two clean parts thoroughly, and never eyeball a structural fillet or a laminating batch you intend to rely on.

Sources & Further Reading
  • Gougeon Brothers on Boat Construction — Gougeon Brothers
  • The Backyard Boatbuilder — Daniel St. John Green
  • West System Technical Data Sheets — Gougeon Brothers / West System