Calculate lumber quantities, weights, and costs for boat building projects
Planked hull construction
Interior joinery and trim
Structural deck framing
"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.
Download NowMarine lumber is bought by the board foot, not the piece, and misjudging that unit is how first-time builders under-order frames, planks and spars or overpay for stock they never use. One board foot is a foot long, one inch wide and one inch thick, and every stick you buy converts to it.
Species matters as much as volume. Mahogany, cypress, cedar and Douglas fir differ in weight, cost and workability, so a cutting list priced across several species tells you the true bill and the displacement the wood will add to the boat.
Add each piece's length, width, thickness and quantity, choose the species, and the calculator totals the board feet, weight and cost, then applies a waste allowance so you buy enough without paying for a pile of offcuts.
Board Feet = (Length × Width × Thickness ÷ 144) × Quantity| Species | lb / board ft | Typical Use |
|---|---|---|
| Douglas Fir | 3.2 - 3.7 | Frames, spars, stringers |
| Western Red Cedar | 2.3 - 2.6 | Planking, lightweight tops |
| White Oak | 3.7 - 4.0 | Bends, keelsons, strength parts |
| Mahogany | 3.7 - 4.2 | Trim, brightwork, planking |
| Cypress | 3.0 - 3.3 | Rot-critical planking |
Approximate green weight and character by marine species.
Formula verified against standard naval-architecture references · Updated October 2026
A board foot is a volume of lumber measuring 12 inches long by 12 inches wide by 1 inch thick, or 144 cubic inches. It is the standard buying unit so that pieces of different widths and thicknesses can be compared and priced fairly. To find board feet, multiply length, width and thickness in inches, divide by 144, then multiply by the number of identical pieces.
Add 15 to 25 percent for a typical build. Straight, clear marine stock wastes less; curly, knotty or narrow boards waste more. Bent frames and long planks generate extra offcuts as you chase grain, so factor a bigger allowance on those. It is far cheaper to return a few unused boards than to stop the build hunting a matching piece.
Yes, and builders often get caught by it. Rough-sawn lumber is measured at its true dimension, while planed (S4S) stock has been shaved down, so a nominal one-inch board finishes nearer three-quarters. Calculate from the actual finished size you will use, otherwise the planed stock leaves you a short of the number of board feet your frames need.
Match the job. Douglas fir is strong, stiff and economical for frames, spars and stringers. Cedar is light and rot-resistant for planking and topsides. White oak bends well and carries heavy loads. Mahogany finishes beautifully for trim and brightwork. Cypress resists decay in wet, unforgiving spots. Choose for strength, weight, rot resistance and cost in that order for each part.
Roughly two to four pounds per board foot depending on species and moisture. Cedar is at the light end near 2.3, fir around 3.5, and heavy oaks and mahoganies above 3.7. Because weight compounds across dozens of frames and planks, tallying board feet times species density gives you a realistic estimate of the wood's contribution to total displacement before you launch.
Both have a place. Kiln-dried lumber is stable, workable and readily available, good for frames, trim and joinery. Air-dried stock is gentler on the wood's strength and is traditional for spars and bent parts. The key for any boat is genuinely dry, well-seasoned timber at working moisture, because wood that later shrinks or rots inside a closed hull is a disaster.
Add a real margin rather than ordering the bare net area, because board footage counts the full board while your cutouts throw away knots, splits, warped ends and the saw kerf between parts. For a straightforward panel job ten to fifteen percent over the calculated area is normal; for a boat full of curved, yielded pieces from clear stock, plan on twenty-five percent or more, since you will reject length after length to find the grain and figure each part needs. Buy the clear, straight, wide boards first and cut the demanding pieces from them, keeping the narrower or busier stock for blocking, jigs and hidden backing where appearance and grain direction do not matter.