Calculate materials, weight, and cost for fiberglass construction
Heavy duty hull layup
Standard deck layup
Lightweight parts layup
"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.
Download NowThe fiberglass layup calculator turns a surface area and a stack of cloth into the real numbers you need at the hardware store: how many ounces of glass, how many pounds of resin, how thick the finished laminate will be, and what the whole job will cost. Getting these right is the difference between a stiff, watertight shell and a heavy, resin-starved or resin-rich mess.
In DIY boatbuilding, fiberglass is used to sheathe a wooden hull, skin a foam core, or build a whole composite shell. Each fabric type — chopped strand mat, woven roving, biaxial, unidirectional, carbon — carries a different weight per square yard and needs a different resin-to-glass ratio. Layering them deliberately is how you tune strength against weight.
Enter your surface area and build a layup schedule layer by layer, and the calculator sums the fabric weight, resin demand, gelcoat, thickness, and cost so you can order once and plan with confidence.
Fabric (lbs) = Area(yd²) × Σ(oz/yd² × plies) ÷ 16| Fabric | Weight (oz/yd²) | Resin:Glass ratio | Common use |
|---|---|---|---|
| Chopped Strand Mat | 10 - 16 | ~3.0 | Bonding, low-cost bulk |
| Plain Weave | 9 - 10 | ~1.4 | Hull sheathing |
| Twill Weave | 7.5 - 8 | ~1.3 | Draped corners, sheathing |
| Biaxial | 17 - 18 | ~1.3 | Structural skins |
| Woven Roving | 24 | ~1.5 | Heavy structural layers |
| Carbon Fiber | 5.8 | ~1.1 | High stiffness, low weight |
Typical cloth weights and resin ratios used in marine hand layup.
Formula verified against standard naval-architecture references · Updated October 2026
A common wooden-hull sheathing schedule is a single layer of 6 to 10 oz cloth over the exterior, which adds only a couple of ounces per square foot once wetted out. Heavier workboats or cold-moulded shells may take two to four plies of 8 to 17 oz cloth. Calculate your area in square yards, choose your plies, and let the calculator give you total glass weight and resin demand.
For hand layup the practical resin-to-glass weight ratio ranges from about 1.1:1 for tightly woven and carbon fabrics up to 3:1 for chopped strand mat, which soaks up a lot of resin. Epoxy systems generally need less resin than polyester for the same cloth because epoxy wets fibre more efficiently. Always follow your specific cloth datasheet and resin manufacturer's guidance.
Epoxy is the DIY favourite for sheathing and composite work: it bonds well, cures at room temperature with little shrinkage, has low odour, and produces a stronger, lighter laminate per ounce. Polyester is cheaper and is what many production boats use with gelcoat, but it is smellier, more brittle, and less forgiving to work with. For sheathing wood or building foam-core panels, choose epoxy.
As a rule of thumb, cured laminate thickness is roughly 0.025 to 0.030 inch per ounce-per-square-yard of glass, so 10 oz cloth gives about 1/4 inch less with a crimp factor, and a sheathing ply of 6 oz is a couple of millimetres. The calculator estimates thickness from your plies so you can hit a target without over-building weight.
Not necessarily. Many strip-plank and cold-moulded builders skip gelcoat, sheathing with cloth and epoxy then fairing and painting with two-part polyurethane or enamel. Gelcoat gives a hard, coloured, glossy mould-side surface useful when building from a plug, but it is brittle and hard to repair well in a home shop, so it is often left off epoxy builds.
Wrinkles come from applying cloth to a curved surface with excess length or too-thick epoxy. Use a lighter cloth on tight turns, wet the surface with resin before laying the cloth, squeegee from centre out to drive air and surplus resin, and let each panel set before tackling the next. Bias or twill weaves drape far better than plain weave over compound curves.
Carbon offers roughly three to four times the stiffness for the same weight as glass, so it earns its keep on spars, rudders, and load-bearing spars where stiffness-to-weight matters. For hull sheathing where cost, impact toughness, and ease of repair dominate, glass is usually the better value. Use the calculator to compare the weight and cost of a carbon schedule against a glass one for the same area.