Download over 500 Boat PlansDownload Now

Frame Spacing Calculator

Calculate even frame spacing for building a boat hull.

Quick Samples
Try these common configurations to get started

24ft Plywood Skiff

Common spacing for plywood construction

35ft Cruiser

Robust spacing for an offshore boat

16ft Dinghy

Wider spacing for a lightweight build

Hull Dimensions
Enter your boat's principal dimensions

e.g., inches, mm

e.g., inches, mm

Download 500+ Boat Plans
About This Tool
The Frame Spacing Calculator is a simple but critical layout tool for boat builders. When setting up the molds or frames for a hull, it's essential that they are spaced evenly to ensure a fair and symmetrical shape. This calculator takes the total length you need to span and your desired frame spacing, and it calculates the exact, even spacing required to fit a whole number of frames. This eliminates guesswork and ensures your setup is accurate from the start.

Key Concepts:

Frame Spacing: The center-to-center distance between transverse frames.
Station Lines: The locations on the plans where the shape of the hull is defined.
Fairness: The quality of a line or surface being smooth and free of bumps or hollows.
Scantlings: The dimensions of the structural members of a boat, including frames.
Download 500+ Boat Plans
Get access to a comprehensive library of boat plans and tutorials.

"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.

Download Now
Frame Spacing Calculator Calculator: What It Does and Why It Matters

Frames are the ribs of a wooden or strip hull, and how far apart they sit decides both the strength of the shell and how hard each plank is to bend across the curves. Space them too wide and planks oil-can and fastenings pull; too close and you add weight, labour and a forest of timber to fair against. The frame spacing calculator turns a target interval into an even, buildable schedule.

It works by dividing the run length by the desired spacing, rounding to a whole number of equal spaces so the frames land evenly, then reporting the true adjusted spacing that fits that count exactly, plus the number of frames needed. The rounding is the point: it removes the awkward half-gap at one end.

Enter the length to be framed and a desired spacing, and the calculator returns the whole number of spaces, the evened-out actual spacing and the total frame count, so your moulds, battens and fastener runs line up without fudging.

The Frame Spacing Calculator Formula
Number of Spaces = round(Length ÷ Desired Spacing); Actual Spacing = Length ÷ Number of Spaces; Number of Frames = Number of Spaces + 1
  • Length — The run along the hull to be framed
  • Desired Spacing — The target interval between frames
  • Number of Spaces — Whole count of equal gaps after rounding
  • Actual Spacing — The evened-out interval that fits the length exactly
  • Number of Frames — Total frames, one more than the gaps
Worked Example: Frame Spacing Calculator Step by Step
  1. 1A 12 foot run, 144 inches, is to be framed near every 16 inches.
  2. 2Number of spaces = round(144 ÷ 16) = round(9) = 9 equal spaces.
  3. 3Actual spacing = 144 ÷ 9 = 16.0 inches, already even in this tidy case.
  4. 4Number of frames = 9 + 1 = 10 frames along the run.
  5. 5Had the length been 150 inches, the count would round to nine spaces again, but the actual spacing would even out to 150 ÷ 9 ≈ 16.7 inches, so no odd stub gap is left at the end.
How to Use This Calculator
  1. Enter the run of length you need to frame.
  2. Set the frame spacing you are aiming for.
  3. Keep both the length and the spacing in one unit.
  4. Read the whole number of equal spaces it rounds to.
  5. Mark out the run using the evened actual spacing.
Frame Spacing Calculator Reference Table
MethodCommon SpacingNote
Strip-plank backing battens6 - 12 inSupports the strips
Plywood / carvel frames12 - 18 inBalanced strength
Clinker light hull8 - 14 inCloser for thin planks
Heavy / high-load areas6 - 10 inNear stations, keel, engine

Typical frame spacings by construction.

What This Means in a Real Build
  • Let the rounding drive the marking, not the wish. Divide, round to whole spaces and then recompute the even spacing, so the first and last frame sit exactly on the ends and every gap is identical; marking straight off an unadjusted target leaves a lopsided half-frame at the stem or transom that is obvious once planking starts.
  • Tighten spacing where the hull is hardest loaded, not everywhere. Engine bearers, the keel, sheer clamps and the areas of sharp curvature want frames closer than the general run, so use the calculated even spacing as the baseline and deliberately reduce it locally rather than framing the whole boat at the closest interval and paying for it in weight.
  • Add a frame where a plank joint lands. Fastening needs backing under every seam and butt block, so let the schedule flex to put a frame beneath a butt or a wide garboard edge; the calculator gives the even grid, and real layout shifts a space here and there so butts never hang unsupported between frames.
  • Count once more than you think. Frames number one more than the gaps, so ten spaces means eleven frames, and forgetting the extra end frame is a routine ordering error that strands you short of timber mid-build; take the reported frame count as your cut list.

Formula verified against standard naval-architecture references · Updated October 2026

Frame Spacing Calculator Calculator: Frequently Asked Questions

How far apart should frames be?

Commonly twelve to eighteen inches for plywood and carvel work, closer for thin planks or strip backing battens, and tighter still near heavy loads. Enter the run length and your target spacing and the calculator rounds it to a whole number of equal spaces so the frames land evenly end to end, and reports the adjusted interval and total frame count to build to.

Why round the number of spaces?

Because a raw length rarely divides evenly by the target spacing, and building to the unadjusted number leaves an odd half-gap at one end. Rounding to a whole count and recomputing the actual spacing spreads the difference across every gap, so all intervals are identical and the terminal frames sit exactly on the stem and transom.

How many frames do I need?

One more than the number of spaces, since frames bracket the gaps. Nine equal spaces means ten frames along the run. The calculator returns both so you can order timber and set cut lists correctly; missing that extra frame is a common shortfall that stalls planking.

Should spacing change along the hull?

The baseline should stay even for fairness, but you deliberately close the spacing where the structure is loaded or the curvature is sharp, near the engine, keel, sheer clamps and fine ends. Treat the computed spacing as the general grid and tighten locally rather than framing everything at the closest interval and adding needless weight.

What unit should I enter?

Any single consistent unit, usually inches for imperial hulls or centimetres for metric, as long as length and desired spacing share it. The spacing arithmetic is unitless, so mixing inches and feet silently is the one error that throws the whole schedule off; keep both inputs in the same measure.

Does this apply to metal or fibreglass frames?

Yes. The geometry is the same whether the frames are timber, bent metal or moulded composite webs; what changes is only the sensible spacing, which is tighter for stiff heavy shells and wider for light ones. Enter the run and the target interval for your material and even out the schedule identically.

Sources & Further Reading
  • Boatbuilding — Howard I. Chapelle
  • Gougeon Brothers on Boat Construction — Gougeon Brothers
  • The Backyard Boatbuilder — Daniel St. John Green