Download over 500 Boat PlansDownload Now

Deadrise Angle Calculator

Analyze your boat's hull performance based on its deadrise angle.

Quick Samples
Try these common configurations to get started

Deep-V Sportboat

22° deadrise, for speed in chop

Moderate-V Cruiser

18° deadrise, balanced ride

Shallow-V Workboat

12° deadrise, stable platform

Hull Dimensions
Enter your boat's principal dimensions

feet

feet

feet (total width of both chines)

Download 500+ Boat Plans
About This Tool
The Deadrise Angle Calculator is a crucial tool for boat designers and builders to determine a hull's 'V' shape. This angle is a primary factor in how a boat performs, affecting its stability at rest, its ability to cut through waves, its speed, and its overall handling characteristics. A deeper V provides a smoother ride in rough water, while a flatter hull is more stable and efficient on calm surfaces.

Key Concepts:

Deadrise Angle: The V-angle of the hull bottom.
Chine: The edge where the hull bottom meets the hull sides.
Stability: Resistance to rolling. Lower deadrise = more stability.
Seakeeping: How well the boat handles waves. Higher deadrise = better seakeeping.
Download 500+ Boat Plans
Get access to a comprehensive library of boat plans and tutorials.

"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.

Download Now
Deadrise Angle Calculator: What It Does and Why It Matters

Deadrise is the angle between a boat's hull bottom and a horizontal line, measured at the transom. It describes how sharp or how flat the hull sits in the water, and it is one of the strongest single influences on how a powerboat rides, turns, and planes.

A high deadrise (a deep V) slices through chop and gives a soft, dry ride offshore but demands more power to lift onto a plane and can feel tender at rest. A low or flat bottom planes instantly, is stable and roomy, and is efficient in calm water but slaps hard in a chop. Moderate-V hulls split the difference and dominate general-purpose runabouts.

This calculator derives the transom deadrise angle from the hull's half-beam and the vertical rise of the bottom at the chine, and reports the corresponding chine angle so you can classify your hull as flat, moderate, or deep-V.

The Deadrise Angle Formula
Deadrise (°) = atan( bottom rise ÷ half-beam ) × 180 ÷ π
  • Deadrise — V-angle of the hull bottom at the transom, in degrees
  • bottom rise — Vertical rise of the keel line above the chine, in inches
  • half-beam — Half the beam width, measured to the chine
  • atan — Arctangent, converting the rise/run ratio to an angle
  • chine angle — Related angle measured to the sheer/deadwood line
  • 180 ÷ π — Converts the radian result to degrees
Worked Example: Deadrise Angle Step by Step
  1. 1A 102-inch-beam hull has a half-beam of 51 inches at the chine.
  2. 2The bottom rises 20 inches from the chine line up to the keel at the transom.
  3. 3Take the ratio: 20 ÷ 51 = 0.392.
  4. 4Arctangent of 0.392 = 0.374 radians, which × 180 ÷ π = 21.4 degrees.
  5. 5That transom deadrise of about 21 degrees puts the boat squarely in the moderate-V category — a good all-round performer for inshore and light-chop cruising.
How to Use This Calculator
  1. Measure the beam at the chine and halve it to get the run.
  2. Measure the vertical rise of the bottom from the chine line to the keel at the transom.
  3. Enter both dimensions in the same units (inches is normal).
  4. Press Calculate to read the deadrise and chine angles.
  5. Use the classification table to see whether your hull is flat, moderate-V, or deep-V.
Deadrise Angle Reference Table
Transom deadriseHull classCharacter
0 - 10°Flat bottomCalm water, shallow draft, stable at rest
11 - 20°Modified-VAll-round inshore, quick plane, soft-ish ride
21 - 24°Moderate-VCruising compromise, good chop handling
25 - 30°Deep-VOffshore, soft dry ride, needs more power
> 30°Ultra deep-VSport fishing / heavy seas

Deadrise bands and their typical behaviour.

What This Means in a Real Build
  • Deadrise changes continuously from bow to stern; the transom figure quoted here is the one that best predicts planing behaviour and ride on a given hull.
  • Raising deadrise buys a softer ride but also more wetted surface and drag when down on a plane — deep-V hulls cruise efficiently only when trimmed and lifting.
  • A flat-bottom skiff is not simply a 'cheap deep-V'; it wins on stability, draft, and shallow-water ability, so match deadrise to where the boat will actually run.
  • Constant-V hulls keep the same angle fore and aft; variable-V designs drop deadrise toward the bow for a drier entry — note which you are measuring.
  • Combine deadrise with beam and weight when judging power needs; a deep-V of the same beam planes later than a modified-V and needs a proportionally bigger outboard.

Formula verified against standard naval-architecture references · Updated October 2026

Deadrise Angle Calculator: Frequently Asked Questions

What is deadrise on a boat?

Deadrise is the angle formed between the hull's bottom surface and a horizontal plane, conventionally measured at the transom. A hull with no V — a flat bottom — has zero deadrise, while a sharp offshore deep-V can be 25 degrees or more. It is the simplest single number that captures how 'V'd' or flat a hull is, and it strongly predicts ride quality and planing behaviour.

What is a good deadrise angle?

It depends on where you boat. Flat to 10 degrees suits calm lakes, flats, and shallow rivers. 11 to 20 degrees (modified-V) is the sweet spot for inshore runabouts and most DIY powerboats — quick planing and reasonably soft. Above 24 degrees pays off only when you regularly run in a real chop offshore; in calm water a deep-V just wastes fuel and space.

Is higher deadrise better?

Higher deadrise cuts through waves and gives a drier, softer ride in rough water, which is why offshore and sport-fishing hulls are deep-V. The trade-off is more drag at rest, a slower and more power-hungry transition onto a plane, and less stable-platform feel when stopped. Better is subjective — the best deadrise matches your typical sea state and duty.

How is deadrise measured on a hull?

At the transom, measure the horizontal distance from the keel line to the chine (the half-beam) and the vertical rise from the chine line up to the keel. Deadrise is the arctangent of rise divided by that horizontal run. On a lofting board or from a lines plan you read the same angle directly off the body section at the aftermost station.

What is the difference between constant-V and modified-V?

A constant-V hull keeps the same deadrise from forward to the transom, common in older deep-V designs. A modified-V (or variable-deadrise) hull has more V forward and flattens toward the transom, often to around 11 to 14 degrees, giving a softer bow entry plus a quick-planing, efficient aft section. Most modern trailerable runabouts are modified-V.

Does deadrise affect fuel economy?

Yes, mainly through drag and how well the hull lifts. At rest and at displacement speeds a deep-V has more wetted surface and burns more. On a plane, a well-chosen deadrise trims and lifts efficiently, but an over-deep hull that never quite gets its aft sections flat will hold more drag and use more fuel than a shallower-V hull of the same power.

Can I change my boat's deadrise during a build?

Not practically once the frames and planking are set — deadrise is built in through chine height and keel rise at each station. What you can tune within an existing hull is planing performance through the amount of afterbody lift, strakes, and trim. That is why the angle is decided on the lofting floor, at design time, before a single plank goes on.

Sources & Further Reading
  • New Classic Boatbuilding / hull-form notes — Chesapeake Light Craft technical library (www.clcboats.com)
  • The Dynamics of Marine Vehicles — R. Bhattacharyya
  • Society of Naval Architects and Marine Engineers (SNAME) (www.sname.org)