Download over 500 Boat PlansDownload Now

Trim Tab Calculator

Calculate the optimal trim tab size for your boat

Quick Samples
Try these common configurations to get started

25ft Sport Fisher

Common V-hull sport boat

30ft Express Cruiser

Heavier cruiser with moderate V

35ft Performance Boat

Deep-V high-speed hull

Hull Dimensions
Enter your boat's principal dimensions
Download 500+ Boat Plans
About This Tool
This calculator helps you select the correct size trim tabs for your boat. Proper trim tab sizing is crucial for improving performance, correcting trim issues, and enhancing fuel efficiency on planing hulls.

Key Concepts:

Span (Width): Affects lateral (side-to-side) trim control.
Chord (Length): Affects the total amount of lift generated.
Deadrise: The angle of the hull bottom, affecting tab effectiveness.
Attitude: The running angle of the boat in the water.
Download 500+ Boat Plans
Get access to a comprehensive library of boat plans and tutorials.

"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.

Download Now
Trim Tab Sizing Calculator: What It Does and Why It Matters

Trim tabs are small adjustable plates on the transom that act like the elevators on an aircraft, letting the driver change the boat's running attitude on the fly. Down with one tab lifts that side of the hull, correcting a list; down with both lifts the stern, dropping the bow and helping a heavy boat get on plane sooner.

Their authority comes from size and speed. Span, the side-to-side width, governs how well the tabs correct list, while chord, the fore-and-aft length, governs how much lift each tab creates. A deep-V hull with a high transom angle needs more chord to be effective than a flat runabout.

Enter boat length, beam, weight, cruising speed and transom angle, and the calculator recommends tab span and chord and estimates the lift force so you can size an automatic or manual trim system that actually moves the hull.

The Trim Tab Sizing Formula
Span ≈ 1 inch per foot of boat length; Chord = 9 in base (12 in for large/fast, +3 in for transom > 15°); Lift ∝ (Span × Chord ÷ 144) × (Speed ÷ 10)²
  • Span — Side-to-side tab width along the transom, roughly an inch per foot of boat
  • Chord — Fore-and-aft tab length that sets how much lift each tab generates
  • Transom Angle — Deadrise at the transom; deeper-V hulls want longer chord
  • Tab Area — Span times chord, the surface that acts on the water
  • Lift Force — The upward or correcting force the tabs produce at speed
Worked Example: Trim Tab Sizing Step by Step
  1. 1A 24 foot deep-V fishing boat, 8 foot beam, 5,000 lb, cruising at 30 knots with a 19 degree transom.
  2. 2Span follows the one-inch-per-foot rule: about 24 inches per tab.
  3. 3Chord starts at 9 inches; the transom angle exceeds 15 degrees, so add 3 inches for an 12 inch chord.
  4. 4Tab area = 24 × 12 ÷ 144 = 2.0 square feet per tab.
  5. 5Lift scales with that area and the square of speed, so 30 knots produces strong authority; at 12 knots the same tabs are far weaker, which is why trim tabs help most once the boat is up and running.
How to Use This Calculator
  1. Enter the overall boat length to set the tab span.
  2. Give the beam so you can sanity-check that span.
  3. Set the displacement and your typical cruising speed.
  4. Enter the transom deadrise angle for the chord add-on.
  5. Press Calculate to read recommended span, chord and lift.
  6. Confirm the tabs fit between the hardware on the transom.
Trim Tab Sizing Reference Table
Boat LengthTab SpanChordApplication
16 - 20 ft16 - 20 in9 inSmall runabouts and skiffs
21 - 26 ft21 - 26 in9 - 12 inFishing boats, bowriders
27 - 34 ft27 - 34 in12 inCruisers and express boats
35 ft+36 in+12 in+Large heavy hulls

Typical trim tab sizing by boat length.

What This Means in a Real Build
  • Mount the tabs as far outboard as the transom allows, because leverage, not raw size, is what corrects list; a wide-spaced pair of modest tabs often beats narrow-spaced large ones.
  • Tabs are a cruise-speed device. Their lift grows with the square of speed, so they do little at low rpm and shine once the boat is up on plane, which makes them ideal for trimming attitude on the run rather than helping a lug half out of the hole.
  • Do not use tabs to fix a loading error. If a boat sits permanently nose-down or lists from weight placement, move the load first; tabs compensate for trim and minor list, they cannot substitute for a badly balanced hull.
  • Automatic systems shine in changing conditions, holding a set attitude without the driver fiddling, while manual tabs suit a boat with a predictable load. Weigh the cost and complexity against how often your trim actually varies.
  • Seal and protect the hardware below the waterline. Trim tabs live in the wettest, most-corroded part of the boat, so good anodes, wiring and a secure attachment are what keep the system working for years.

Formula verified against standard naval-architecture references · Updated October 2026

Trim Tab Sizing Calculator: Frequently Asked Questions

What size trim tabs do I need?

Follow the rule of thumb of roughly one inch of span per foot of boat length, with chord around nine inches for smaller or flatter boats and twelve or more for larger, faster or deep-V hulls. The calculator applies those increments and adds chord for a high transom angle, then checks span against beam so the tabs fit the transom and deliver real authority.

Do trim tabs help a boat get on plane?

They help indirectly. At speed, dropping both tabs raises the stern and lowers the bow, reducing the planing surface needed and easing a heavy hull over the hump, but their lift depends on water flow so they are weakest exactly when you are trying to come onto plane from a stop. Correct prop, trim and load first; tabs then fine-tune the attitude once flowing.

Manual or automatic trim tabs?

Manual tabs are cheaper and simpler and suit a boat whose load rarely changes. Automatic systems sense attitude and adjust continuously, which is worth it on a cruiser whose loading, sea state and speed vary widely and whose owner wants a set-and-forget ride. Match the control to how much your running attitude actually changes between trips.

Can trim tabs correct a persistent list?

They can mask a mild list by lifting the low side, but a strong, constant list usually means uneven weight or a hull or ballast issue that tabs are hiding rather than solving. Use tabs for on-the-fly trim and light correction; if you are permanently holding a tab down to stay level, find and fix the underlying imbalance instead.

Where should the tabs be mounted?

As far apart and as low on the transom as the hull shape and hardware allow, typically within a few inches of each side. Wider spacing gives more leverage for list correction, and full submersion at rest ensures they work before you are up to speed. Keep them clear of the prop streams and any strakes or pads that would disturb the flow over them.

Do tabs affect fuel economy?

Used well they can improve it, because trimming a boat to a flatter, lower-drag attitude lets it run more efficiently at a given speed and can let you back off the throttle. Used badly, streamed out at the wrong angle, they add drag and cost economy, so treat them as a trim tool to find the flattest, lowest-resistance attitude rather than a free lift.

Sources & Further Reading
  • The Backyard Boatbuilder — Daniel St. John Green
  • Propeller Handbook — Dave Gerr
  • ABYC Steering and Control Standards — American Boat and Yacht Council