Estimate the static and dynamic thrust of your boat's propeller
High-power outboard on a sportfisher
Electric trolling motor on a small boat
Diesel cruiser with a large propeller
"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.
Download NowThrust is the pushing force that actually moves a boat, and it is the number that decides whether an engine can get a heavy hull onto plane, hold position against current, or tow a water skier out of the hole. Horsepower tells you the energy available; thrust tells you how much shove that energy delivers at a given moment.
Two very different figures matter. Static thrust at zero speed is the maximum push a prop can make standing still, which governs planing and towing, while dynamic thrust falls as speed rises and the prop bites through already-moving water. Both come from power, propeller disc area and the density of the water accelerated through it.
Enter horsepower, propeller diameter and boat speed, and the calculator estimates static and dynamic thrust and compares them to hull weight so you can see whether the drivetrain will lift and drive the boat you are building.
Static Thrust (N) = ∛(Power W² × 2 × ρ × Disc Area); Dynamic Thrust (lb) ≈ (HP × 375 × efficiency) ÷ Speed| Condition | Thrust Trend | Implication |
|---|---|---|
| Zero speed (static) | Maximum | Best for planing and towing |
| Low speed | High | Getting the boat over the hump |
| Cruise speed | Moderate, falling | Must exceed total drag |
| High speed | Low | Limited reserve for waves |
How thrust behaves with speed and load.
Formula verified against standard naval-architecture references · Updated October 2026
As a rough guide a planing hull needs available thrust, at the moment of getting over the hump, comfortably greater than its drag at that speed, often on the order of a fifth to a quarter of its weight for a typical recreational hull. The calculator compares static and dynamic thrust to hull weight so you can see whether the prop and power will actually lift the boat rather than merely spin.
Static thrust is the maximum push at zero speed, when the prop accelerates still water and the whole power goes into shove; it governs starting, planing and towing. Dynamic thrust is the reduced push available as the boat speeds up, because the water is already moving through the prop. Both fall from the same power, but they answer different questions about acceleration versus sustained speed.
Usually yes, for a given power. A larger propeller sweeps a bigger disc of water and produces more thrust at lower rpm, which is exactly what heavy or underpowered boats want. The limit is clearance and the ability to still turn fast enough to reach rated engine rpm, so the best choice is the largest wheel that fits and grips without overloading the engine.
Because for fixed power, thrust falls as speed rises; the prop is pushing against water that is already moving, so less of the energy becomes shove and more goes into overcoming drag. That is inherent to propulsion, not a fault, and it is why the usable margin for waves and acceleration is greatest at low and medium speed and thinnest at the top of the range.
No. Horsepower is the rate of energy delivered; thrust is the resulting force on the boat. The same horsepower produces different thrust depending on propeller size, pitch, rpm and speed. A big slow prop converts power into high thrust at low speed, ideal for towing, while a small fast one makes less thrust but suits high-speed running, which is why matching the prop matters as much as the engine.
Look at low-speed thrust, not top-speed horsepower. Pulling a skier out of the water and holding them up is a near-static-thrust problem, so a boat needs plenty of push at modest speed, which favors pitch and diameter that load the engine heavily at low rpm. Use the static and dynamic figures here to judge whether the drivetrain has the shove the job demands.
They are sound engineering estimates from momentum theory and the power-speed relationship, not measured bench data. Real thrust depends on propeller design, efficiency, clearance and hull interference, so treat the results as a reliable range for comparing options and confirming the drivetrain is plausible, then trust a tachometer and a loaded sea trial to settle the final choice.