Download over 500 Boat PlansDownload Now

Planing Hull Calculator

Analyze planing hull performance and power requirements

Quick Samples
Try these common configurations to get started

25ft Center Console

Typical V-hull sport boat

32ft Express Cruiser

Heavier cruiser with a modified-V

28ft Performance Boat

Deep-V for high speed and rough water

Hull Dimensions
Enter your boat's principal dimensions
About This Tool
This calculator uses simplified versions of the Savitsky and Crouch formulas to estimate the performance characteristics of a planing hull. It helps determine the required horsepower and minimum planing speed.

Key Concepts:

Planing Lift: Hydrodynamic force that lifts the hull out of the water.
Deadrise: The V-angle of the hull, affecting ride and efficiency.
Speed-Length Ratio: A key indicator of planing efficiency.
Power-to-Weight: The main driver of acceleration and top speed.
Download 500+ Boat Plans
Get access to a comprehensive library of boat plans and tutorials.

"My Boat Plans" is a collection of over 500 boat plans, from simple dinghies to larger cruisers. It includes step-by-step guides, video tutorials, and more.

Download Now
Planing Hull Analysis Calculator: What It Does and Why It Matters

A planing hull is a machine for trading power against weight to lift the boat onto its own wake and skim across the surface, and the design lives or dies on whether it has enough planing surface and enough power to get and stay up there. Get it right and the boat rides fast and dry; get it wrong and it ploughs, squats and drinks fuel.

The key relationships are the power needed to lift a given weight to a given speed, which grows with the square of speed, and the planing surface length that the beam and weight imply. Deadrise shapes the trade between a soft, dry ride in a deep-V and efficient, flat running in a shallow hull.

Enter displacement, beam, deadrise and target speed, and the calculator estimates the power required, the implied waterline and planing surface, and the speed-length ratio so you can see whether the hull and engine genuinely match the mission.

The Planing Hull Analysis Formula
Required Power = Weight ÷ (Speed ÷ Crouch C)²; C = 210 flat, 190 standard, 180 deep-V; Planing Speed ≈ 1.6 × √LWL
  • Weight — Loaded displacement the hull must lift onto plane
  • Speed — Target planing speed in knots
  • Crouch C — Hull constant: 210 flat, 190 standard, 180 deep-V
  • LWL — Waterline length implied by weight and beam
  • Speed-Length — Ratio of speed to the square root of length, a planing measure
Worked Example: Planing Hull Analysis Step by Step
  1. 1A 4,000 lb boat, 8 foot beam, 17 degree deadrise, aiming for 35 knots.
  2. 2A 17 degree hull is standard, so Crouch C = 190.
  3. 3Required power = 4000 ÷ (35 ÷ 190)² = 4000 ÷ (0.184)² = 4000 ÷ 0.034 = about 118 hp at the shaft.
  4. 4Implied waterline from weight and beam is roughly 4000 ÷ (0.01 × 8²) = 4000 ÷ 0.64 ≈ 19 feet, giving a planing threshold near 1.6 × √19 ≈ 7 knots.
  5. 5The 35 knot target is well above planing speed and the ratio confirms the boat must be genuinely lifted, which is why the power number, not hull speed, governs this design.
How to Use This Calculator
  1. Enter the loaded displacement in pounds.
  2. Give the beam that sets the planing surface.
  3. Select the deadrise angle to pick the constant.
  4. Set the target planing speed you want.
  5. Read the required horsepower and the length ratios.
  6. Check the power-to-weight figure against your engine.
Planing Hull Analysis Reference Table
DeadriseCrouch CRideEfficiency
Under 15° (flat)210Hard in chopMost efficient
15 - 21° (standard)190BalancedGood all-round
Over 22° (deep-V)180Soft, dryThirstier
Variable deadrise185 - 195Fine forwardModern compromise

Deadrise, Crouch constant and ride character.

What This Means in a Real Build
  • Pick deadrise for where you boat, not for looks. A deep-V carries its ride offshore but pays in weight, wetted surface and fuel on flat water, while a flatter hull is quicker and cheaper in calm conditions and punishing in a chop.
  • Weight is the lever you control in design and loading. Because required power grows directly with displacement, a boat planned at 100 hp for a light load can need a very different engine once tanks, batteries and gear go in, so size to the heaviest expected condition.
  • Planing surface has to be long enough. A short, wide hull with hard chines can lift on modest power, but a hull without enough flat aft surface will squat and never truly plane, so the beam-length balance matters as much as raw horsepower.
  • Trim and drive-angle decide how hard the boat has to work. A hull held nose-high climbs its own wave and wastes power, so set the outdrive or shaft angle and tab trim so the boat rides level at cruise, unlocking speed the numbers say is available.
  • Treat the planing-speed threshold as the floor, not the target. Below roughly 1.6 times the square root of waterline length the boat is largely in displacement mode; the interesting design work is the power needed well above it, which is what this calculator quantifies.

Formula verified against standard naval-architecture references · Updated October 2026

Planing Hull Analysis Calculator: Frequently Asked Questions

How much power does it take to plane?

Required power grows with the square of target speed and directly with displacement, using a Crouch constant that reflects the hull. A 4,000 lb standard-V boat wanting 35 knots lands near 120 shaft horsepower, and doubling the weight doubles that. The calculator applies the deadrise-derived constant so you can see the honest power a planing hull needs at your chosen speed and load.

What deadrise angle should my hull have?

Match it to conditions. Flat hulls under fifteen degrees are fast and efficient on calm water but slam in a chop. Standard sixteen to twenty degrees balances ride and economy for general boating. Deep-Vs over twenty-two degrees cut offshore comfort but cost wetted surface, weight and fuel. Choose the softest ride you actually need, because deeper V always takes efficiency.

Why is my boat hard to get on plane?

Usually not enough power, too much weight, or a too-high transom. Trim, prop and load come first: a boat sitting nose-down in the water, an over-pitched prop or a heavy stern all raise the power needed to lift it. Check displacement against the design figure and that the prop lets the engine reach rated rpm before blaming the hull.

Does beam help a boat plane?

It adds planing surface, which helps the hull lift and support its weight, and a wide, flat transom is a classic fast-cruiser recipe. But beam also adds wetted surface and initial drag at rest, and too much of it with insufficient length squat-and-drag rather than fly, so it is the balance of beam and waterline length that matters, which is why the calculator derives waterline from both weight and beam.

What is the speed-length ratio?

It is speed divided by the square root of waterline length, and it expresses how hard a hull is working relative to its length. Values near one mean near hull speed; well above one means genuine planing. A planing boat often runs at ratios above two, and the number tells you whether the hull and power have truly lifted the boat onto its wake or it is still ploughing.

Can I upgrade to plane without new engine?

Sometimes, by shedding weight, correcting trim, changing the prop to let the engine reach rpm, and adding tabs or a shallower drive angle to reduce the planing surface needed. These can lift a marginal boat onto plane at a slightly lower speed. If you are far short of the calculated power, however, no trim trick replaces the missing horsepower.

How accurate is the power estimate?

It is a reliable planning figure that captures the dominant physics of weight, speed and hull form. Real results vary with the exact run of the bottom, chine design, prop and loading, so treat the number as the centre of a sensible engine range and confirm against boats of similar design and, ultimately, a loaded sea trial.

Sources & Further Reading
  • Elements of Yacht Design — Francis Hervey Skene
  • High-Speed Water Craft (Crouch) — SNAME Transactions
  • The Backyard Boatbuilder — Daniel St. John Green